WALDO Sighting

29 Oct 22:

Our shop stool WALDO is Skipper's favorite to put her feet on while she Skippervises, it was spotted today returning from the work deck. Surprisingly WALDO did not get any Kirby Paint splattered onto it while we were painting EXCUSE ME.

 Log of the Boat Shop Stools

Signal Kilo Stool and Birdhouses

 19 Mar 22:

Used some spare boat paint today to finish up the shop stool and birdhouses. Here's the signal Kilo stool, for my first name initial.

There is some TotalBoat Wet Edge Black, White, Fire Red, Kingston Gray and Yellow in the mix, along with Interlux Brightside Largo Blue. We also got the North point painted.

Shop Stool from Scraps

28 Jan 22: 

I was making a bookcase and screwed up the shelf measurement, too short, so after I sat in the moaning chair a bit I decided to take some of the scraps and make another shop stool. First we cut out the legs, braces and top using our patterns.

Then I cut out the handles..

...and the toe grab.

Screwed on the legs.

Attached the braces and the top.

She's in the paint shop, she'll get a Kilo signal flag paint scheme.

John Gardner Boat Shop Stool Signal Bravo

 20 Feb 21:

Traced the patterns onto scrap cypress. 1 top step, 2 legs, 1 center brace and 2 side braces. Cut them out with the DeWALT 20V jigsaw.

To cut the handhold into the center brace we drill a starter hole for the jigsaw blade.

It is easier to round most of the edges before assembly using a 1/8th inch roundover bit on our DeWALT compact trim router. Some edges, like where the side braces attach to the legs, are better left square. Also it would be easier to paint all the pieces before assembly, but I was impatient.

Marked fastener holes with an awl.

We used #10 silicone bronze screws, 2 1/2 inches long, predrilled pilot hole and countersunk with a Fuller combination pilot hole and countersink bit. Long screws help hold everything together.

Ready for paint.

Intermission. Skipper wanted to visit Opal Beach, the road has just now opened after Hurricane Sally damage Sep 2020.

We coated the stool with TotalBoat WetEdge Fire Red, BlueGlo White and Halcyon Clear Satin Varnish.

One of our crew's first name initial is B, so the step stool got Signal Flag Bravo colors.

FMI: Gardner Boat Shop Stool

Gardner Boat Shop Stool Pattern and Second Stool

02 Dec 18:

We made a pattern for our Gardner shop stool WALDO a while back and cut out the first test pieces from a scrap of 1/2 inch marine grade plywood. Finally put the pieces together with #10 silicone bronze wood screws, rounded off the edges with a 3/4 inch roundover bit. Everything fit great. Now it's getting a paint job, its name is CARMEN, as in Where In the World is Carmen San Diego, continuing the theme of where are the shop stools? She will keep WALDO company.

Boat Shop Stool Log.

Mystic Seaport John Gardner Boat Shop Stool

I saw a shop stool in the John Gardner Boat Shop at Mystic Seaport and wanted to make one for our shop. It will be helpful to reach some top shelf items, pegboard over the sink and in a pinch could double as a moaning chair.

From SBR 4: Jun 2014 -

I contacted the Museum and one of their staff was kind enough to take measurements from their stool and send them to me.

From SBR 4: Jun 2014 -

Ran up to Lowes and picked up a piece of 1"x12"x8' Select Pine. Looks like I have some other pending projects waiting patiently in the back of the Edge....

From SBR 4: Jun 2014 -

Drew the line for the 17 inch wide top first.

From SBR 4: Jun 2014 -

Cut the top with a circular saw. This project is small enough that you could use a set of cordless tools.

From SBR 4: Jun 2014 -

Traced lines for the legs.

From SBR 4: Jun 2014 -

Traced lines for the sides.

From SBR 4: Jun 2014 -

Traced lines for the center support and used sides to help draw the correct angle. The plan measurements are a bit off for the center support top width.

From SBR 4: Jun 2014 -

I measured the picture of the stool to get a general idea of how wide and tall the arch is on the legs.

From SBR 4: Jun 2014 -

The hand hold on top is just over 4 1/2 inches in diameter. I used the cap from a 5 inch inspection port to get the approximate size.

From SBR 4: Jun 2014 -

I grabbed my level to draw the hand hold cross bar, but I ended up trimming it later as it was too wide. What I used the second time was a scrap piece of the 1x lumber, that gave me the width to match the center support below.

From SBR 4: Jun 2014 -

I used the cap from a 6 inch port to get the approximate arch for the legs.

From SBR 4: Jun 2014 -

Drilled a 1/4 inch starter gole for the jigsaw blade.

From SBR 4: Jun 2014 -

Cut out the top handhold and also cut out a section of the center support with a jigsaw.

From SBR 4: Jun 2014 -

Cut out the leg arch with a jigsaw and then used leg 1 as a pattern for leg 2.

From SBR 4: Jun 2014 -

From SBR 4: Jun 2014 -

Dry fitting the pieces to see if the support angles and widths match up. I did not cut any bevels on the legs or supports as the angle formed between the legs and top is negligible.

From SBR 4: Jun 2014 -

Drilled pilot holes and counterbor for the screws and then assembled the base.

From SBR 4: Jun 2014 -

Used a router bit to round over the edges of the stool. The piece feels better this way, and you get rid of sharp edges that can gouge.

From SBR 4: Jun 2014 -

I centered up the top and traced around the base. Then I set the base upright, flipped the top and used a tape measure to make sure top was centered up again. That way I had a idea of where the edges of the base were when I drilled pilot holes for the screws.

From SBR 4: Jun 2014 -

Finished up the assembly with #8 1 1/2 inch brass screws. Here are the tools and materials that I used.

From SBR 4: Jun 2014 -

Assembly finished, waiting for paint.

From SBR 4: Jun 2014 -

I need the stool so I can reach the keel of the Penobscot 14 with a plane and bevel the keel.

From SBR 4: Jun 2014 -

The stool could also be used to carry a few tools to the job site.

From SBR 4: Jun 2014 -

First coat of Interlux Fire Red.

From SBR 4: Jun 2014 -

Did some operational testing and found out the end arch is just big enough for a toe hold, handy to reposition the stool.

From SBR 4: Jun 2014 -

From SBR 4: Jun 2014 -

Put the stool back into the shop, rounded the corners and put on the second coat of Interlux Fire Red.

From SBR 4: Jun 2014 -

The project took about 2 hours, not including the trip to Lowes.

Paint splatters next? Nope, we'll let it develop its own patina :)

Fair Winds,
Kent